Question: What Type Of Resistor Should I Use?

Do I need a resistor for LED?

LEDs typically require 10 to 20mA, the datasheet for the LED will detail this along with the forward voltage drop.

For example an ultra bright blue LED with a 9V battery has a forward voltage of 3.2V and typical current of 20mA.

So the resistor needs to be 290 ohms or as close as is available..

What is the best type of resistor?

Between the three types of resistors based on composition, carbon-composition resistors, carbon-film resistors, and metal-film resistors, in overall performance, metal-film resistors are the best, carbon-film the next best, and carbon-composition resistors last.

What are the 4 types of resistors?

Different Types of Resistors – Fixed, Variable, Linear & Non-Linear Resistors & ApplicationsCarbon Composition Resistors.Wire wound Resistors.Thin Film Resistors.Carbon Film Resistors.Metal Film Resistors.Thick Film Resistors.Metal Oxide Resistors.Cermet Oxide Resistors (Network Resistors)More items…

What happens if I use the wrong resistor?

If you are using such a resistor in a current-sensing application in a switch-mode circuit, you will get spurious readings or inaccurate behaviour. … For a simple LED circuit there are no bad consequences of using a resistor of higher power.

Can I use a higher ohm resistor?

2 Answers. The cases where using a higher value resistor will damage a circuit exist, but are a bit less usual than the cases where it may simply produce a weaker result than desired, or a different frequency response than desired.

How do you know what size resistor to use?

A rule of thumb is to find a resistor with twice the power rating. Here I would choose a 250 mW resistor since those are the most standard ones. Usually, you can just use the cheapest resistor you can find with the correct power rating.

What does R mean in resistors?

Resistors have the symbol on the right. Resistance is defined as the voltage developed across the resistor per ampere of current through the resistor. Resistance has a symbol of R measured in unit called Ohm which has a symbol Ω.

What resistor should I use with my LED?

Basics: Picking Resistors for LEDsPower Supply VoltageLED ColorResistor (rounded)3 VRed, Yellow, or Yellow-Green51 Ω4.5 VRed, Yellow, or Yellow-Green39 Ω4.5 VBlue, Green, White, or UV51 Ω5 VBlue, Green, White, or UV68 Ω4 more rows•Aug 29, 2012

What are the two types of resistor?

Basic distinction of resistor typesFixed resistors: Fixed resistors are by far the most widely used type of resistor. … Variable resistors: These resistors consist of a fixed resistor element and a slider which taps onto the main resistor element.

Can I use a different resistor?

Sometimes you need a resistor with a value you don’t have in your kit. Instead of ordering and wanting for a resistor with a value you need you can change the resistance of a resistor by using another resistor or many. By installing resistors in a parallel or series circuit you can change the value in Ohms.

What is inside the resistor?

Most common, modern resistors are made out of either a carbon, metal, or metal-oxide film. In these resistors, a thin film of conductive (though still resistive) material is wrapped in a helix around and covered by an insulating material. … Inside the resistor, a carbon film is wrapped around an insulator.

What happens if you don’t use a resistor with an LED?

When hooking up an LED, you are always supposed to use a current-limiting resistor to protect the LED from the full voltage. If you hook the LED up directly to the 5 volts without a resistor, the LED will be over-driven, it will be very bright for a while, and then it will burn out.

Should I put a resistor before or after the LED?

It doesn’t matter! The resistor can go before – or after – the LED, and it will still protect it. the current that flows out of a battery is always equal to the current that flows back into the battery.